Airsoft Forum & MILSIM Forums

Airsoft Forum & MILSIM Forums (http://www.airsoftsociety.com/forums/)
-   General Accessory Discussion (http://www.airsoftsociety.com/forums/f13/)
-   -   ignite black ops m4 viper front hand grip swap? (http://www.airsoftsociety.com/forums/f13/ignite-black-ops-m4-viper-front-hand-grip-swap-71915/)

airsoftmerc 03-04-2013 08:51 PM

ignite black ops m4 viper front hand grip swap?
 
I want to switch out the standard hand grip on my ignite black ops m4 viper for a quad rail. Is it possible and how much would it cost?

soviet 03-04-2013 08:55 PM

Quote:

Originally Posted by airsoftmerc
I want to switch out the standard hand grip on my ignite black ops m4 viper for a quad rail. Is it possible and how much would it cost?

Um.... If it uses a standard rail, getting a new grip should be fine.

Superto4ster 03-04-2013 09:02 PM

It depends on the delta ring, some hand guards require a real steel delta ring and some don't.

soviet 03-04-2013 09:13 PM

Quote:

Originally Posted by Superto4ster
It depends on the delta ring, some hand guards require a real steel delta ring and some don't.

I doubt a Walmart one requires real steel parts my friend..

Superto4ster 03-04-2013 09:15 PM

True, but is the whole gun TM compatible or just internals?

soviet 03-04-2013 09:23 PM

Quote:

Originally Posted by Superto4ster
True, but is the whole gun TM compatible or just internals?

I don't think it is TM compatible.

StealthyApple 03-27-2013 11:59 PM

still looking for an answer to this too.
here's my thread.. http://www.airsoftsociety.com/forums/f10/black-ops-ignite-m4-viper-external-modifications-73361/#post863936

EPWrestler 03-28-2013 02:57 AM

I have one also, and I recently purchase a magpul hand guard and it fits perfectly. It even works if u still have it wired to the front, hope this helps.

kingfhb 03-28-2013 06:35 PM

I put a Magpul MOE forward hand guard on recently.... now it's for a REAL AR15, but they do make the PTS versions as well.
I had to modify the location of the front sight for it to fit properly because its a bit long. Not sure if the PTS version is or not.
What would happen is that the "gas tube" wouldn't reach the main part of the "upper" to prevent the barrel from twisting. To fix this, all you have to do is remove the front sight, and then drill a small hole further back from the original and run your pin through it (instead of the forward one) and then you're good to go. Oh, and I also relocated the sling mount, but it is plastic anyway and more than likely wouldn't hold the gun in it's current state.

The rail is sturdy and holds everything I've thrown at it without issue. I've seen some POLY quad rails that appear as if they would fit very nicely online. Dboys makes one, AIM Sports makes one, NcStar makes one... there's a bunch... check eBay also.

I've seen plenty of quad rails that would fit on this D-ring as it matches my real AR. The fact that it's plastic has not been an issue at all. For that matter, this gun is so close to the real AR, you could probably purchase a real dela ring and quad and fit it on fine. I was considering buying a low profile gas block for a real AR and putting it on to remove the front sight all together. It secures to the barrel and would negate the need for the pin to hold the gas block, because then you could adjust the length and simply tighten it down.

http://www.districtnola.com/000/7.jpg
http://www.districtnola.com/000/15.jpg
http://www.districtnola.com/000/14.jpg
http://www.districtnola.com/000/13.jpg
http://www.districtnola.com/000/12.jpg
http://www.districtnola.com/000/11.jpg
http://www.districtnola.com/000/10.jpg
http://www.districtnola.com/000/9.jpg
http://www.districtnola.com/000/8.jpg

YES, this is a Wal-Mart Ignite Black Ops M4.

1. Magpul MOE Stock
2. Magpul PTS Vertical Grip
3. Magpul PTS Airsoft AEG
4. Magpul MOE forward hand guard (had to modify the location of the front sight for it to fit properly, but it only took drilling a new hole for the pin that holds the gas tube in place so the barrel won't turn).
5. Magpul PTS rear Flip up sight.
6. Dboys AN/PEQ2 Battery Box (holds battery, but with enough room to modify it to add a real "Varmint Hunter" Flashlight and Laser with pressure switches on Vertical Grip).
7. Aimpoint M3 Red/Green Dot Scope with Larue Mount
8. Aimpoint 3x Magnifier with flip to the side Larue Mount
9. Magpul PTS Ambidextrous single point sling ring.
10. Magpul MS3 Sling (Not shown)

Otherwise it's stock with the original magazine.

Quote:

I doubt a Walmart one requires real steel parts my friend..
This is an EXCELLENT gun for $99. All metal gears and inner parts. Shoots true, adjustable hop-up, blow back, great FPS... I would recommend it to anyone looking to get into the game and doesn't have $299 to spend. (Though mine has now FAR exceeded that $99).

Carpathia 03-28-2013 06:39 PM

Holy crap. You spent a lot of money upgrading a Walmart gun, or did you already have all that stuff on hand?! Did you repaint the body too (notices the lack of Ignite Black Ops Trademarks)? It looks pretty sweet, how does it perform?


All times are GMT. The time now is 07:38 AM.

Powered by vBulletin®
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.