Peeque's Recent Activity

  1. Peeque liked aotsukisho's post in the thread JG/GE/LT M16A3 won't fire..

    Yep, pulled off the grip then used flathead screwdriver on one of the bevel gear ratchets to remove tension off the ARL and unhooked the...

    Apr 20, 2021 at 3:55 PM
  2. Peeque liked Dead_Christmas's post in the thread JG/GE/LT M16A3 won't fire..

    Thanks everybody. The tools are coming out of Saint Paul, so we won't have to wait years for it. Once I get them, I'll work my trog...

    Apr 19, 2021 at 8:57 PM
  3. Peeque replied to the thread KWA R47 Upgraded and Extras.

    Ok. Just wondering. Someone I played with on Saturday had a gun that looked just like yours.

    Apr 19, 2021 at 3:19 AM
  4. Peeque liked Dead_Christmas's post in the thread JG/GE/LT M16A3 won't fire..

    Indeed! I was able to successfully reassembly at least one AK gearbox in my lifetime. I'm just absolutely **** at soldering and figuring...

    Apr 18, 2021 at 10:19 PM
  5. Peeque replied to the thread JG/GE/LT M16A3 won't fire..

    I think you said you've worked on a V.3 before? The V.2 is very similar looking inside to the V.3. So you shouldn't have too much trouble.

    Apr 18, 2021 at 10:15 PM
  6. Peeque replied to the thread JG/GE/LT M16A3 won't fire..

    If you try to take the gearbox apart before pulling the ARL and letting the spring decompress it's gonna blow up when you go to lift the...

    Apr 18, 2021 at 10:08 PM
  7. Peeque replied to the thread JG/GE/LT M16A3 won't fire..

    You need to relieve the pressure on the ARL from the bevel gear by turning it by hand. You will need to use a screw driver or some kind...

    Apr 18, 2021 at 9:55 PM
  8. Peeque replied to the thread KWA R47 Upgraded and Extras.

    Are you in PA?

    Apr 18, 2021 at 7:56 PM
  9. Peeque replied to the thread JG/GE/LT M16A3 won't fire..

    Some gearboxes have a little cut out on the top or bottom shell in line with the ARL for easy access. If yours has that, push it...

    Apr 18, 2021 at 6:13 PM
  10. Peeque liked Guges Mk3's post in the thread Bearings on spring guide / piston head.

    And the bearing on the spring guide/piston head came about due to a design flaw from Long Soft springs - It's all SystemA's fault. It...

    Apr 18, 2021 at 4:12 PM
  11. Peeque liked aotsukisho's post in the thread Recommended Ak12 Upgrades.

    Stock Marui-spec gear ratios are 18:1, actually 18.72:1. Dropping in a 16t motor and running it on 11.1v 3s lipo should get you close...

    Apr 18, 2021 at 12:20 PM
  12. Peeque liked danerd's post in the thread Recommended Ak12 Upgrades.

    Ive had consistently bad experiences from both G&P and Lonex motors. G&P for whatever reason like shed arm windings and Lonex magnets...

    Apr 18, 2021 at 12:20 PM
  13. Peeque liked aotsukisho's post in the thread Lancer Tactical Enforcer BATTLE HAWK 7" Skeleton AEG (LT-34).

    I've made some posts about them in the past, they should be very similar in terms of information. I'll copy them here for convenience...

    Apr 18, 2021 at 8:34 AM
  14. Peeque liked aotsukisho's post in the thread Bearings on spring guide / piston head.

    The 3rd reason why you shouldn't is because the Tokyo Marui spec does not use bearings on either end, and by putting two thrust bearings...

    Apr 18, 2021 at 8:05 AM
  15. Peeque liked danerd's post in the thread Bearings on spring guide / piston head.

    Running bearings on both can cause a few issues: 1. Rotational forces between the SG and PH can be different and lead to the spring...

    Apr 17, 2021 at 10:13 PM