Recent Activity

Activity stream for all registered members at Airsoft Society - Community for Airsoft and Milsim Enthusiasts.

  1. Peeque replied to the thread Nylon spacers for correcting AoE.

    I won't be printing Nylon anytime soon. I will need to upgrade some things on my printer before I can do that. I went with these,...

    Apr 15, 2021 at 9:44 PM
  2. Peeque liked Guges Mk3's post in the thread Echo 1 red star Ak 47 RIS / Lipo ready? Battery?.

    Any 2S LIPO that fits will be just fine. So it came with this Large NIMH battery (Sub-Cells)? The plug that is large (molex type) in...

    Tamiya.JPG kyosho.JPG Apr 15, 2021 at 9:34 PM
  3. Guges Mk3 attached a file to the thread Echo 1 red star Ak 47 RIS / Lipo ready? Battery?.

    Any 2S LIPO that fits will be just fine. So it came with this Large NIMH battery (Sub-Cells)? The plug that is large (molex type) in...

    Tamiya.JPG kyosho.JPG Apr 15, 2021 at 8:38 PM
  4. CCRBUM replied to the thread Looking for a GBBR MP5..

    I ordered my son's TM gen4 glock 17 from KYairsoft and it arrived without an issue... took maybe a month? but arrived in one piece. I'm...

    Apr 15, 2021 at 8:12 PM
  5. aotsukisho liked Peeque's post in the thread V3 Titan Trigger Issue.

    I had the same issue with one of mine. For me, the motor connectors were loose on the tabs. I couldn't tell you why this was causing...

    Apr 15, 2021 at 7:30 PM
  6. Guges Mk3 replied to the thread FS: Rare KJW M4A1 Circa 2014 - Demo Unit - 5 Gas Mags with no Leaks.

    Zips don't it?

    Apr 15, 2021 at 7:26 PM
  7. Jimps replied to the thread V3 Titan Trigger Issue.

    That is a good thing to check, I thought that as well. Ill check motor connections. It just shoots so well would not think that would be...

    Apr 15, 2021 at 6:45 PM
  8. Peeque replied to the thread V3 Titan Trigger Issue.

    I had the same issue with one of mine. For me, the motor connectors were loose on the tabs. I couldn't tell you why this was causing...

    Apr 15, 2021 at 6:40 PM
  9. Jimps replied to the thread V3 Titan Trigger Issue.

    I put the sticker in the trigger to get rid of backlash. It is a MP5k so I have to use the stock trigger, which I do not like. I had to...

    Apr 15, 2021 at 6:35 PM
  10. Peeque replied to the thread Nylon spacers for correcting AoE.

    I can't find 1/2" wide spacers anywhere that are the correct lengths and ID or the tubes to extend the piston head nipple. Maybe I can...

    Apr 15, 2021 at 6:19 PM
  11. aotsukisho replied to the thread V3 Titan Trigger Issue.

    Is the screw holding the Titan down threadlocked and secured properly? Did you apply the sticker on the trigger lever to remove...

    Apr 15, 2021 at 5:01 PM
  12. aotsukisho replied to the thread Nylon spacers for correcting AoE.

    3/8" (9.5mm) I don't think is wide enough as the cylinder has a bore of around 24mm or 15/16" (24mm)? You'd want the support to be as...

    Apr 15, 2021 at 4:54 PM
  13. aotsukisho replied to the thread Incorporating a Fuse into Mosfet.

    You need to know both the hold current and likely fault current of your application, along with the temperature that the PTC fuse will...

    Apr 15, 2021 at 4:47 PM
  14. Richard Paoletti liked Guges Mk3's post in the thread Airsofters with glasses?!?.

    I was not aware that some of you were perceiving my comments as they were, when I reread my post it didn't seem offensive in any way,...

    Apr 15, 2021 at 4:11 PM
  15. GrimWolf0770 replied to the thread Airsofters with glasses?!?.

    And before you say it no I will not act my age!!!!>: P

    Apr 15, 2021 at 4:07 PM
Loading...