Airsoft Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 86 Results
  1. Gun Building, Modifications & Repairs
    So I have this problem where when i try to load my glock with bb's it's like the loading nozzle doesn't push the bb into the pipe correctly, so it gets stuck kind of in between the magazine and the pipe. This makes it so that I have to tilt the pistol a bit to roll the bb into the the pipe and...
  2. Gun Building, Modifications & Repairs
    Hello all! I have a friend that recently got the KLI Baba Yaga from an Airsoft GI mystery box, and it had a few issues the first time he used it. First of all, when he tries to fire, sometimes it won't, and the trigger feels like it is a two-stage trigger even though it did not before. could...
  3. Gun Building, Modifications & Repairs
    Ok so it doesnt seem to matter whatever i try, but whenever shooting in semi, and sometimes on full auto, the gears takes an extra half cycle leaving the nozzle retracted which then happens to let 2 BB's into the chamber. Ive tried different gears, pistons, springs, motors, tappet plates. Should...
  4. Gun Building, Modifications & Repairs
    I’ve installed a Perun V2 hybrid into my cyma platinum MP5. Everything works fine until I plug the motor in. Occasionally I get a couple shots off and then the mosfet stops detecting that the motor is connected. What’s weird is that when I increase the motor height by a huge amount, sometimes...
  5. Gun Building, Modifications & Repairs
    Looking for assistance. I have a new umbrella MK-18. The first 30 or 40 shots of every mag are very low velocity and drop about 10 feet in front of me. I'm using epm 1 mags 200 rd midcaps. Any tips?
  6. Gun Building, Modifications & Repairs
    Hi! I've been having issues with the pistonhead scratching the inside of the cylinder, specifically the bottom side of the cylinder. It was probably a cause of bad aoe but now that is corrected with the piston also having the first 2 teeth filed down. Changed the cylinder and polished the...
  7. Introductions
    My HFC baretta M9 is running into issues. My mag is not leaking as i can not hear any gas escaping. When it is in semi auto it feels like there isn’t as much kick as there uses to be and it is shooting a bb every other trigger pull or so. Once I put it in full auto it will shoot some blanks then...
  8. Gun Building, Modifications & Repairs
    Warning this will be a loong read!! Alright i need fresh pair of eyes on this one, got the gun second hand from a guy who supposedly only used it a couple of times. And externaly and internaly it does look almost brand new, completely stock. So first thing i had to do was change the hop unit...
  9. General Airsoft Discussion
    Warning this will be a loong read!! Alright i need fresh pair of eyes on this one, got the gun second hand from a guy who supposedly only used it a couple of times. And externaly and internaly it does look almost brand new, completely stock. So first thing i had to do was change the hop unit...
  10. Scenarios & Milsim
    Hey y’all, I’m wanting to start doing higher level milsim like Milsim west and whatnot, however I know my current setup will not hold up to the standards I need. I’m looking for a pretty high quality high performance M4/AR-15 replica and I need some guidance on what brands and features I need to...
  11. Gun Building, Modifications & Repairs
    Alright let's figure this out haha. I just bought a lonex A1 titan motor, rated at 40k high speed and high torque. I wanna build off that to upgrade my gearbox. I've never upgraded a gearbox, I just want a reliable and well performing setup. So, what are your recommendations for everything. I'll...
  12. Gun Building, Modifications & Repairs
    Striker with a Ariens bolt I want to know if I should upgrade that bolt and hop up system or leave be I want to take the jewels up for a 3.79 up to a jewel of 5.0 or higher if I can make it pro level.and I have a Samurai edge Avalon VFC m4 with a maxx pro hop up and clear and black bushings and...
  13. General Airsoft Discussion
    I will be relocating for a new job and I need to get rid of all my airsoft gun and gears because I just never had time anymore to use them. For the most part they were only used for 1 game and it's been sitting around, no issues, like new conditions. Full metal m4, hard case, vest, etc. All...
  14. Gun Building, Modifications & Repairs
    i recently got a vorsk eu17 and it was working flawlessly until all of a sudden when i had loaded up a mag and tried to shoot it it just went BOP and all of the green gas just hissed out it was quite cold 9 degrees Celsius and I don't if it could have something to do with it if anyone has an...
  15. General Accessory Discussion
    i just got the eglm 40mm launcher for my scar. i removed the orange cap to paint it for mil sim and a spring with a oddly shaped metal piece came out as soon as i removed the the black tube from its tan housing. i have no idea where this goes now. im new to airsoft please help...
  16. Beginners Forum
    Kythera build. Hello, Any advice on my parts list would be helpful :). I don't want to "bottleneck" my build with a relatively underperforming part. Thanks in advance. Base gun: m4 style g&g G4 cqbs Stock v2 gearbox Barrel: Lapped brass 6.01mm by 275mm Hop up: maxx CNC (mi - sport) I don't...
  17. Gun Building, Modifications & Repairs
    Base gun is a KWA TK.45C SE I bought on release. Converted to a DSG in November of 2019 with these parts: Siegetek 14:1 9-tooth dsg set ASG 22TPA motor (moved to 28TPA in June of 2020) SHS 14.5T lightened piston (with extra teeth removed) Lonex POM piston head (w/o bearings) - Important note...
  18. Electric Guns
    Hello Guys, First let me tell the specs, VFC HK416A5 - w\ Titan Gate Hop-up Maxx with purple buckling Battery Titan 7.4v 3000mAh I live in Italy so the gun should be strictly below 1 J. So problem is that 1 out of 7\8 shots at the crono from an avg. of 0.80J goes up to 1.10J, basically the...
  19. Gun Building, Modifications & Repairs
    I'm trying to change the spring of my snow wolf m4 and once I've got to the part where I remove the gearbox from the lower, we'll... it won't come out, I've removed all the pins and the bolt catch but now the only thing that prevents me from removing the gearbox is the ambidextrous selector...
  20. Gas Powered Guns
    Hello there! I just purchased the strangest, most beautiful airsoft shotgun I have ever seen at an airsoft store from among their boneyard weapons, and I cannot find anything about it online. Here's what I know: It's full metal It uses green gas, loaded directly into the bottom of the gun...
1-20 of 86 Results
Top