Airsoft Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 50 Results
  1. Gun Building, Modifications & Repairs
    I’ve installed a Perun V2 hybrid into my cyma platinum MP5. Everything works fine until I plug the motor in. Occasionally I get a couple shots off and then the mosfet stops detecting that the motor is connected. What’s weird is that when I increase the motor height by a huge amount, sometimes...
  2. Gun Building, Modifications & Repairs
    So the problem I'm having is that my new long type ZCI motor sits too high on the bevel gear. It's high enough that when I'm shimming using the half shell method, the bevel gear tilts down towards the motor and becomes completely stuck. When I compare the ZCI motor to the stock one, the ZCI...
  3. Gun Building, Modifications & Repairs
    I'm trying to find replacement motor brushes for asg motors. I contacted ASG and they basically told me to screw off and find them on my own. There is only one website selling them but only has 1 in stock and isn't in the US. Not even asg offers to sell them wholesale apparently, they don't even...
  4. Gun Building, Modifications & Repairs
    Alright so whenever I plug the battery in their is no beep because it doesn’t sense the motor engaging the bevel. Then when I tighten the motor height higher I get the beep but that motor height is way to high. I am honestly stumped thanks to anyone who helps :)
  5. Gun Building, Modifications & Repairs
    Alright let's figure this out haha. I just bought a lonex A1 titan motor, rated at 40k high speed and high torque. I wanna build off that to upgrade my gearbox. I've never upgraded a gearbox, I just want a reliable and well performing setup. So, what are your recommendations for everything. I'll...
  6. Gun Building, Modifications & Repairs
    So, as some of you may know, I have a CYMA AIMS (CM.050) that I'm planning on upgrading. Part of this includes a Tienly GT-35000 motor, which I got yesterday and installed today. However, when I installed it, the gun wouldn't fire. I'm DEAD CERTAIN I did everything right, from plugging the...
  7. Articles
    Another test sponsored by @Guges Mk3, this time of a motor. A Tienly that was behaving un-Tienly-like, to paraphrase Guges. Motor arrived in its packaging bubble wrapped 25K medium, looks okay at first glance Looking down at the endbell, springs and brushes look fine It doesn't appear...
  8. Gun Building, Modifications & Repairs
    So, i am quite new to the hobby, and bought a used AK105 rifle with a lot of modifications. The problem now is that it is a high speed DSG build, with some feeding problems as well. First all specs of the rifle: - SHS Dual Sector gear, low gearing ( 20/1) - 1.2J on a SHS M150 fjeder. - ASG...
  9. Electric Guns
    Somewhere, I read that real steel AK pistol grips won't fit airsoft AKs because the airsoft pistol grips are longer to accommodate the motor. Is this true?
  10. Gun Building, Modifications & Repairs
    Hey Guys I just finished with my upgrades to my Nemesis X9 (reshim, regrease, AOE correction). Let me tell you. The trigger response is greatly improved. However, I have noticed that I still experiance motor heat up. Not as bad as the old hunk of crap stock motor but still warm after 5 minutes...
  11. Gun Building, Modifications & Repairs
    Hi everyone, I'd like to know if there'll be any issue if I only upgrade the motor on my Cyma AK This is the parts list: SHS piston SHS purple air nozzle with o ring E&L silenced POM heads Stock gears Stock ball bearing spring guide Stock spring Shoots about 83 m/s with 0.23g bbs I was...
  12. Gun Building, Modifications & Repairs
    I have ordered a Matrix M125 to put in the Echo 1 SCAR I got from a recent trade, which at the moment is sitting at around 200 fps. Will it burn out the stock motor? Or will I just need to be careful about my rate of fire? Honestly I'm only experienced with modding bolt action sniper rifles...
  13. Gun Building, Modifications & Repairs
    Hi everyone, I have quite a few specific questions pertaining either to the v2 or v2.5 extended gearbox builds I’m doing. Trying to troubleshoot feeding (80% or so of shots ‘wump’) and low fps issues (~150fps with an M170) in my v2.5 AR-10 led me to all sorts of diagnostic techniques, including...
  14. Gun Building, Modifications & Repairs
    Was playing a game today and what sounded like my trigger contacts burning out happened. The gun held down on full auto on safety. The gun is a DBoys M4 PDW, which I bought off of trooperx a year ago. Mods are: high speed gears, 6.01 tight bore barrel, firestorm neo magnets, and a picossr3 fet...
  15. Gun Building, Modifications & Repairs
    This is the gun i'm talking about in this thread. --> https://www.airsoftgi.com/product/AGM-MP031-M4A1-Carbine-AEG-Airsoft-Rifle-Black-4539/ I bought this gun from a friend who was leaving airsoft and it shot fine, used it for a few games. Then I put it into storage and when I pulled it out and...
  16. Gun Building, Modifications & Repairs
    Hello, i am new to airsoft and i am looking to upgrade my G&G Raider-L. I want to upgrade my spring to a m130 but idk what brands are good and what brand i should get to also upgrade my motor, i saw a asg infinity cnc u-40000 but idk if that will be enough power or not. Thank you
  17. Articles
    Dang, the pics aren't working....I'll work on that. Let me know if you guys can see this! I got this motor from @Guges Mk3 to test out because he wanted more people to try Tienly motors and offered to sell me one for a very good price. So I bought the motor and a couple other things and said...
  18. Articles
    I got this motor from @Guges Mk3 to test out because he wanted more people to try Tienly motors and offered to sell me one for a very good price. So I bought the motor and a couple other things and said I'd do a review and see if they're worth the money. Apparently this is a gen 3 and Tienly is...
  19. Gun Building, Modifications & Repairs
    Anyone have any experience with them? Are they any good (strong magnets? TPA?). I'm seeing them on ebay for only $30, so it's pretty tempting.
  20. Beginners Forum
    So, recently I decided to order parts for my gun, just external stuff didn't want to mess with anything on the inside of the gun. I bought a new pistol grip for my cqb m4 and after switching it out the gun didn't work. After watching a video I realized I put the wires in the wrong spot after...
1-20 of 50 Results
Top