Airsoft Forum banner
Cancel

TM HK416D Repair

2912 Views 10 Replies 3 Participants Last post by  Ben3721, 
M
Hello, I'm writing this to ask if anyone knows where I can get replacement parts for my TM HK416D? Mine fell and broke at the rear of the lower receiver. Air gun Trigger Gas Gun accessory Gun barrel

Attachments

See less See more
Reply
Save
Like
1 - 11 of 11 Posts
Ben3721
Oh man... I feel terrible for you. That is some bad luck.

I'll start looking for ya.

Edit: This is a next gen TM right? I searched the internet pretty deep and the best I could find is next gen aftermarket m4 lowers. I read something that the next gen m4 lowers are not compatible with the 416 ambidextrous selector. So that might be a issue.

Dont buy anything till some others see this thread.
Reply
Save
Like
M
Ben3721 said:
Oh man... I feel terrible for you. That is some bad luck.

I'll start looking for ya.

Edit: This is a next gen TM right? I searched the internet pretty deep and the best I could find is next gen aftermarket m4 lowers. I read something that the next gen m4 lowers are not compatible with the 416 ambidextrous selector. So that might be a issue.

Dont buy anything till some others see this thread.
Click to expand...
Yes, this is a TM NGRS HK416D.
I tried looking for a replacement but all the search results showed up as "Out of stock".
Reply
Save
Like
Ben3721
MochiFrontLine said:
Yes, this is a TM NGRS HK416D.
I tried looking for a replacement but all the search results showed up as "Out of stock".
Click to expand...
That's the same thing I noticed. Makes me wonder if this issue is common. Maybe another brand that's in stock for the 416 exist.
Reply
Save
Like
M
Ben3721 said:
That's the same thing I noticed. Makes me wonder if this issue is common. Maybe another brand that's in stock for the 416 exist.
Click to expand...
would it be a good idea to try using JB Weld as an alternative?
Reply
Save
Like
Ben3721
MochiFrontLine said:
would it be a good idea to try using JB Weld as an alternative?
Click to expand...
While you could try, there is a high chance it will just pop apart soon after again.
Reply
Save
Like
Guges Mk3
JB weld on the load bearing piece...no.

You are out of luck. Even in Japan the lowers are hard to find. You could solder and retap it...if you are good enough...

Reply
Save
Like
Ben3721
The only other thing I can think of is getting a next gen m4 lower and modifying it to work.

It appears those next gen shells dont have the typical bolt into the gearbox spring guide like a V2 to take some of the stress off the lower reciever.
Reply
Save
Like
M
Guges Mk3 said:
JB weld on the load bearing piece...no.

You are out of luck. Even in Japan the lowers are hard to find. You could solder and retap it...if you are good enough...

Click to expand...
Yeah, I don't think I'd be capable enough to do that :p
Reply
Save
Like
M
Ben3721 said:
The only other thing I can think of is getting a next gen m4 lower and modifying it to work.

It appears those next gen shells dont have the typical bolt into the gearbox spring guide like a V2 to take some of the stress off the lower reciever.
Click to expand...
I see.
Someone on reddit also recommended that.
But I also ended up contacting a bunch of sites, including Impulse101's site which replied back that they would be putting in orders for new stock.
Rectangle Font Slope Circle Parallel
See less See more
Reply
Save
Like
Ben3721
MochiFrontLine said:
Yeah, I don't think I'd be capable enough to do that :p
Click to expand...
Yeah seems involved lol... sanding all paint off... solder it, sand it, repaint... if it was mine I would. But I would know the afterpaint would never last.

Edit: Man now part of me wants to solder a gearbox shut and send it off for a "basic spring upgrade" for sick kicks lol

Seriously though I would find out how you can get a m4 next gen lower to fit that thing.
Reply
Save
Like
1 - 11 of 11 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Airsoft Forum
A forum community dedicated to Airsoft owners and enthusiasts. Come join the discussion about optics, builds, gear, events, reviews, accessories, classifieds, and more!
Full Forum Listing
Explore Our Forums
Gun Building, Modifications & Repairs Staging Area General Airsoft Discussion Electric Guns Clothing / Gear
Top